What Are The Steps Of Riveting?

Aug 15, 2025 Leave a message

The riveting process varies slightly depending on the riveting method (e.g., cold riveting, thermal riveting, automatic riveting, etc.) and specific application scenarios, but the whole process can be summarized in the following core steps. Here are the details:
1.Preliminary preparations
Preparation of materials and tools
Connections: ensure clean, oil-free, burr free surface, the prefabricated holes processed as designed (hole diameter less than rivet diameter, generally less than 0.1-0.3mm).
Rivets: Choose the appropriate materials (e.g. steel, aluminum, copper, etc.), diameter and length to ensure they match the connecting parts.
Tools: Select tools based on riveting methods, such as manual rivet guns, pneumatic riveting machines, hydraulic riveting equipment or thermal riveting equipment (e.g. heating furnaces, induction heaters).
Security protection
Operators are required to wear protective glasses, gloves, etc., to prevent rivets from flying or burning.
Ensure that working areas are well ventilated, especially during thermal riveting, and that high temperature burns and harmful gases are avoided.
2.Riveting operation steps
1. Cold Rivet (Ambient Rivet)
Suitable for riveting with small diameter (generally ≤ 8 mm) and good plasticity (e.g. low carbon steel, aluminum rivets).
Steps:
Positioning and clamping: Adjust and clamp the connecting parts to ensure that the prefabricated holes are concentric.
Rivet: insert the rivet stem into the prefabricated hole with the rivet head near the surface of the connecting member.
Pressurized:
Manual rivet gun: Deformed rivet stem by applying pressure through handle or lever.
Pneumatic/ Hydraulic Riveter: Adjust pressure parameters to start equipment to complete riveting.
Molding inspection: rivet head must be flat, crack free, and close to the surface of the connecting part, no gaps.
2. Heat rivets
Suitable for rivets with larger diameter (>8mm) or higher hardness carbon steel, stainless steel).
Steps:
Heat rivets:
WHOLE HEAT: Place the rivets in heating furnace or induction heater and heat to a plastic temperature (usually 700-900°C).
Local heating: Heat rivet rod with flame spray gun.
Quick insertion and riveting: Plug heated rivets quickly into the prefabricated hole and immediately apply pressure to complete the deformation.
Cooling and inspection: after riveting natural cooling, check riveting head molding quality and connection strength.
3. Automatic riveting (production line application)
Suitable for mass production of automobile, aviation manufacturing etc..
Steps:
Robotic positioning: Positioning parts and rivets connected by robotic arms or automated equipment.
Automatic feeding: Rivets are automatically fed into the riveting position by means of a vibrating plate or a nail feeder.
Pressure control: Hydraulic or servo systems accurately control riveting pressure and timing.
Quality detection: Real-time detection of rivet mass (such as rivet head height and diameter) through sensors or visual systems.
3. Riveted post-treatment
Appearance inspection:
Rivet heads should be complete without cracks or burrs.
The surface of the connecting parts shall not be deformed or scratched.
Dimension checks:
Measure the diameter and height of the rivet head to ensure that it meets the design requirements.
Strength test:
Connectivity is verified by tensile or shear tests.
Antisepsis:
Rivets are spray-painted, galvanized and other anticorrosion treatment to extend the service life.
4. Common problems and solutions
Causes of problems and solutions
Poor forming Insufficient pressure riveting head or too short adjusting pressure parameters or extending riveting time
Rivets too large or too small hole diameter to be drilled anew or replaced with properly sized rivets
Concentration of stress or insufficient material strength at the edge of the hole optimizes the the chamfer or increases the material thickness
When riveting, rivets oxidize too long or cool too slowly, Control heating time, speed up cooling speed
V. Preventive measures
Rivets and hole diameter match: Too small a hole diameter can prevent rivets from being inserted, and too large a hole diameter can affect connection strength.
Riveting order: For multi-riveting connections, rivets must be riveted in symmetrical order to avoid deformation of the connecting parts.
Heat riveting safety: Heat rivets and tools are very hot, so insulating gloves are needed to avoid direct contact.
Environmental requirements: riveting environment must be dry, dust-free, so as not to affect riveting quality.
The above steps and precautions can guarantee the quality and reliability of riveting. Riveting, as a kind of traditional mechanical connection, has been widely used in aerospace, automobile manufacturing and construction because of its advantages of simple operation, low cost and reliable connection.